Agrandir l'image
| Impedance | |
| Mic Input: | 600/1200/2400 ohm |
| DI input: | >1 Mohm/82 pF |
| Output: | < 60 ohm |
| Frequency response @ -3 dB: | 5 Hz to 60 kHz |
| Distortion THD+N @ 40 Hz | ||
| 0 dBU | < 0,10 % | |
| +10 dBU | < 0,10 % | |
| Max. output: | +26 dBU | < 1 % THD |
| Max input without PAD: | +6 dBU | < 1 % THD |
| Max input with PAD: | +26 dBU | < 1 % THD |
| Noise Rg=200 ohm | ||
| Gain: | +20 dB | +60 dB |
| 22Hz-22kHz: | < -82 dBU | < -60 dBU |
| CCIR-468-4: | < -72 dBU | < -50 dBU |
| CMRR @ 10 kHz: | < -60 dB |
| Gain : | |
| Mic Input: | -10 +70 dB |
| DI input: | 0 to 60 dB |
| Tubes | |
| ECC 82 | 2 pcs. |
| ECC 83 | 4 pcs. |
| Dimensions | |
| Height: | 2 units 88 mm 3,5" |
| Width: | 483 mm 19,0" |
| Depth: | 165 mm 6,5" |
| Weight | |
| Net: | 4,3 kg 9,5 lbs. |
| Shipping: | 6,1 kg 13,4 lbs. |
| Power requirements: | |
| @ 115V/230V | 30-45W |
TUBE9E4D0D
Nouveau
TUBE TECH - MP2A
The MP 2A is a combined mic preamp/DI, based on a classic TUBE-TECH design, but featuring even higher fidelity and a few new features: An impedance switch to match the input perfectly to all types of microphones, an overload indicator and 2 dB gain steps
MP2A is the second in the new range of upgraded microphone preamplifier/DI's.( The modular PM1A was the first.) These new preamps features even higher headroom and fidelity than the earlier TUBE-TECH micpre''s.
Serious listening tests of the MP 2A have revealed a sound quality second to none, placing it among a handful of the worlds very best designs.
The MP 2A DI continues the TUBE-TECH tradition of extremely good sounding DI's, delivering world class sound for bass and guitar DI recordings. You simply won’t find a better DI than this!
The TUBE-TECH MP2A is a combined Microphone Preamplifier and Direct Instrument amplifier.
The input provides switchable +48 V phantom power, selectable mic. impedance of 600/1200/2400 Ohm, phase reverse switch, low-cut filter (20 Hz/40 Hz/off), as well as a switchable -20 dB pad.
Gain is adjustable from +10 dB to +70 dB.( 10db steps, coarse +2 dB steps, fine.) The Direct Instrument Input are unbalanced with a gain ranging from + 10 dB to + 60 dB.
The amplifier is all tube. Input transformer is enclosed in a MU-metal can. Input and output transformers come with a static screen between the primary and secondary wirings. The input and output are balanced as well as fully floating.
- All-tube design featuring push-pull output amplifier
- Frequency response @ -3 dB: 5 Hz to 60 kHz
- Typical noise: 5 dB @ 200Ω
- CMRR: > 60 dB @ 10 kHz
- Gain: +10 dB to +70 dB in 2 dB steps - DI gain: 0-60 dB
- Selectable mic input impedance: 600 Ω/1.2 kΩ/2.4 kΩ
- Selectable pad in front of input transformer (-20 dB)
- Selectable +48 V phantom power
- Low cut filter (20 Hz/40 Hz/Off)
- Phase reverse
- Overload indicator
- Gold plated switches
- DI jack input for a variety of instruments
- DI input impedance > 1 MΩ
- MU-metal shielded input transformer
- In- and outputs are transformer balanced and fully floating
Features And Specs
| Impedance | |
| Mic Input: | 600/1200/2400 ohm |
| DI input: | >1 Mohm/82 pF |
| Output: | < 60 ohm |
| Frequency response @ -3 dB: | 5 Hz to 60 kHz |
| Distortion THD+N @ 40 Hz | ||
| 0 dBU | < 0,10 % | |
| +10 dBU | < 0,10 % | |
| Max. output: | +26 dBU | < 1 % THD |
| Max input without PAD: | +6 dBU | < 1 % THD |
| Max input with PAD: | +26 dBU | < 1 % THD |
| Noise Rg=200 ohm | ||
| Gain: | +20 dB | +60 dB |
| 22Hz-22kHz: | < -82 dBU | < -60 dBU |
| CCIR-468-4: | < -72 dBU | < -50 dBU |
| CMRR @ 10 kHz: | < -60 dB |
| Gain : | |
| Mic Input: | -10 +70 dB |
| DI input: | 0 to 60 dB |
| Tubes | |
| ECC 82 | 2 pcs. |
| ECC 83 | 4 pcs. |
| Dimensions | |
| Height: | 2 units 88 mm 3,5" |
| Width: | 483 mm 19,0" |
| Depth: | 165 mm 6,5" |
| Weight | |
| Net: | 4,3 kg 9,5 lbs. |
| Shipping: | 6,1 kg 13,4 lbs. |
| Power requirements: | |
| @ 115V/230V | 30-45W |
