Agrandir l'image
Size and Weight
| Height: | 3.5 inches (8.89 cm) |
| Width: | 19 inches (48.26 cm) |
| Depth: | 17 inches (43.18 cm) |
| Weight: | 26 pounds (11.79 kg) |
Power Configuration
- Internal AC Supply
- 100VAC-240VAC (different fuse for 100V,
- 115V, and 240V)
Dc1 Dual Mode Compressor Data
Size and Weight
- THD+N: (@+4dB, with no compression but
- through gain cell)
- 0.025% (A weighted), 0.041% (unweighted with
- 6dB compression) 0.013% (A weighted), 0.013%
- (unweighted)
- Frequency Response: 5dB >200kHz +/- 3dB,
- 5Hz-136kHz +/-0.5dB
- Gain: -4dB to +10dB
- Attack: variable from 4mS to 100mS
- Release: variable from50mS to 1S
- Ratio: Classic or Tight
- Metering: 10 segment LED for gain reduction
- IO: Balanced XLR +4dB in and out,
- 1/4" side chain, 1/4" stereo link
Db2- Drive Bus Master Output and Overdrive
Size and Weight
- THD+N (@+4dB, no cut or boost):
- Bypass: 0.002% (A weighted), 0.008% (unweighted)
- Tube: 0.3% to overdrive (unweighted)
- Solid State: 0.013% to overdrive (unweighted)
- Frequency Response:
- Tube 5Hz -> 50kHz +/- 2dB, 5Hz -> 25kHz +/- 0.5dB
- Solid State 5Hz- > 200kHz +/- 2dB, 5Hz-130kHz +/- 0.5dB
- Gain: +20dB
- Type: Tube (12AX7A) or discrete transistor
- Metering: analog VU output level
- IO: balanced XLR +4dB in and out, -10dB 1/4" TRS out
Mz2 Microphone Preamplifier
Size and Weight
- Max gain: +60dB (plus 20dB when routed
- through the Db2 drive bus output)
- THD+N (@ +30dB): 0.008% (A weighted), 0.01% (unweighted)
- Max Out: +25dB
- Frequency Response: Solid State 10Hz-200kHz +/- 3dB;
- 15Hz-120K +/-0.5dB
- Tube 15Hz-159K +/-3dB, 0Hz-65Hz +/- 0.5dB
- Input impedance: 2K ohms
- Type: Switchable tube (12AX7A) or discrete transistor
- HPF: 60Hz, 6dB/8va
- Metering: 10 segment LED
- Phantom Power +48VDC
- Pad: -20dB
- Polarity: 0 or 180 degrees
- IO: Balanced XLR mic in, front panel 1/4" Hi-Z in, balanced XLR +4dB
- (nominal) out, 1/4" TRS -10dB (nominal)
Fe1- Passive 3 Band Equalizer
Size and Weight
- THD+N (@+4dB, no cut or boost): (A weighted) 0.009%,
- (unweighted) 0.025%
- Frequency Response: 5Hz- 100kHz +/-0.5dB ,
- 5Hz- >200kHz +/-3dB
- Frequencies:
- Low 33, 60, 100, 150, 270, 390HZ (peak or shelf)
- Mid peaking bandwidth: 2 octaves
- High shelf: 6dB/8va, peaking bandwidth 2 octaves
- IO: balanced XLR +4dB in and out
SUMMIT704D
Nouveau
Summit Audio - ECS-410 Everest Channel Strip
Mz-2 Mic & Inst. Preamp
The Mz-2 is a spectacular sounding microphone and instrument preamplifier with the ability to switch between tube and solid-state input stages.
DC-1 Dual Mode Dynamics
The Dc-1 module is an ultra low noise dynamics control section with switchable Classic “soft knee” smooth compression or Tight mode, which provides a much higher compression ratio.
Fe-1 Passive EQ
The Fe-1 Passive Equalizer offers up three bands of smooth Summit passive tube EQ with fixed frequency select knobs with six settings each.
Db2 Drive Bus/Output
The Db2 Drive Bus has multiple gain stages for overdriving in either vacuum tube or discrete transistor mode, allowing for all sorts of tonal variation from ultra clean to overdrive.
All for one, one for all
Everest is a state of the art channel strip comprised of four completely independent modules, each with its own fully balanced input and output, and the ability to effortlessly route and reroute each module internally entirely in the analog domain.
TouchPatch and go
With the TouchPatch routing system you're in control of your signal path quickly and efficiently. With just the push of a button, you can easily route any combination of the ECS-410 internal modules.
Take the direct route
Each section has its own I/O (and in some cases, multiple I/O), so each one can be wired into your patch bay for individual use. Any section not routed internally is ready to be used on its own as if it were a completely independent piece of gear….and all six of Everest’s outputs are always on and available, allowing for all sorts of creative routing and patching options..
Hand-crafted in the USA
Each piece of Summit gear is meticulously crafted by hand in our shop using only the best quality components and attention to detail. Quality components and engineering know-how are the critical element to the sound and longevity of audio gear.
Features And Specs
Size and Weight
| Height: | 3.5 inches (8.89 cm) |
| Width: | 19 inches (48.26 cm) |
| Depth: | 17 inches (43.18 cm) |
| Weight: | 26 pounds (11.79 kg) |
Power Configuration
- Internal AC Supply
- 100VAC-240VAC (different fuse for 100V,
- 115V, and 240V)
Dc1 Dual Mode Compressor Data
Size and Weight
- THD+N: (@+4dB, with no compression but
- through gain cell)
- 0.025% (A weighted), 0.041% (unweighted with
- 6dB compression) 0.013% (A weighted), 0.013%
- (unweighted)
- Frequency Response: 5dB >200kHz +/- 3dB,
- 5Hz-136kHz +/-0.5dB
- Gain: -4dB to +10dB
- Attack: variable from 4mS to 100mS
- Release: variable from50mS to 1S
- Ratio: Classic or Tight
- Metering: 10 segment LED for gain reduction
- IO: Balanced XLR +4dB in and out,
- 1/4" side chain, 1/4" stereo link
Db2- Drive Bus Master Output and Overdrive
Size and Weight
- THD+N (@+4dB, no cut or boost):
- Bypass: 0.002% (A weighted), 0.008% (unweighted)
- Tube: 0.3% to overdrive (unweighted)
- Solid State: 0.013% to overdrive (unweighted)
- Frequency Response:
- Tube 5Hz -> 50kHz +/- 2dB, 5Hz -> 25kHz +/- 0.5dB
- Solid State 5Hz- > 200kHz +/- 2dB, 5Hz-130kHz +/- 0.5dB
- Gain: +20dB
- Type: Tube (12AX7A) or discrete transistor
- Metering: analog VU output level
- IO: balanced XLR +4dB in and out, -10dB 1/4" TRS out
Mz2 Microphone Preamplifier
Size and Weight
- Max gain: +60dB (plus 20dB when routed
- through the Db2 drive bus output)
- THD+N (@ +30dB): 0.008% (A weighted), 0.01% (unweighted)
- Max Out: +25dB
- Frequency Response: Solid State 10Hz-200kHz +/- 3dB;
- 15Hz-120K +/-0.5dB
- Tube 15Hz-159K +/-3dB, 0Hz-65Hz +/- 0.5dB
- Input impedance: 2K ohms
- Type: Switchable tube (12AX7A) or discrete transistor
- HPF: 60Hz, 6dB/8va
- Metering: 10 segment LED
- Phantom Power +48VDC
- Pad: -20dB
- Polarity: 0 or 180 degrees
- IO: Balanced XLR mic in, front panel 1/4" Hi-Z in, balanced XLR +4dB
- (nominal) out, 1/4" TRS -10dB (nominal)
Fe1- Passive 3 Band Equalizer
Size and Weight
- THD+N (@+4dB, no cut or boost): (A weighted) 0.009%,
- (unweighted) 0.025%
- Frequency Response: 5Hz- 100kHz +/-0.5dB ,
- 5Hz- >200kHz +/-3dB
- Frequencies:
- Low 33, 60, 100, 150, 270, 390HZ (peak or shelf)
- Mid peaking bandwidth: 2 octaves
- High shelf: 6dB/8va, peaking bandwidth 2 octaves
- IO: balanced XLR +4dB in and out
