RADIAL - SPACE HEATER 500 Agrandir l'image
Specifications are subject to change without notice.
Circuit type:  Thermionic Gain stage with solid state input and output buffers
Frequency response: 20Hz - 20KHz ± 1dB
Total harmonic distortion:  Varies with Drive and Level settings
Dynamic range:  92dB
Input impedance – bypassed:  50K
Input impedance – active:  1M
Maximum input:  +20dBu
Maximum gain:  32dB@140V, 27dB @70V, 13dB @35V
Clip level - output:  +22dBu 
Output impedance:  100Ω 
Equivalent input noise:  -102dBu 
Noise floor:  -70dBu 
Intermodulation distortion:  Varies with drive and level settings 
Common mode rejection ratio:  -60dB
Unity gain control position:  Drive & level at about 11 o'clock
Features   
Controls: Drive, Level, Hi-Cut filter, Lo-Cut filter
Switches:  "Heat", EQ Pre/Post, IN 
Switches - rear panel:  Heater polarity selection
Filter slopes:  12dB/Octave 
Omniport function:  Unbalanced instrument input
General   
Construction:  500 Series module
Finish: Durable powder coat
Size: (W x H x L) 5.3" x 1.6" x 6.7" (134mm x 40mm x 170mm)
Weight:  1.55lb
Shipping size: (W x H x L): 6.7" x 1.9" x 9.1" ( 170mm x 48mm x 231mm)
Shipping weight: 2lb
Conditions: For use in dry locations only between 5°C and 40°C
Warranty:  Radial 3-year, transferable

Plus de détails

RADI29E431

Nouveau

0 € HT

Prix conseillé: 0 €
Vous économisez: 0 € (0.00 %)

RADIAL - SPACE HEATER 500

Radial

The Radial Space Heater 500™ is a studio-grade tube distortion for the 500 series format. Built to provide anything from subtle warmth to thick and heavy harmonic distortion, the Space Heater 500 is both useful and fun!

Designed for use in the Radial Workhorse or any other 500 series rack, the Space Heater is built around a 12AX7 tube. First, a drive control lets you determine the amount of signal passing through the tube. Next, a 3-position heat switch allows you to apply 35, 70 or 140 volts at the plate to change how the tube reacts to the signal. At the low 35V setting the tube is starved for voltage which causes the tube to break up at a very low volume. The middle 70V setting is a great starting point and allows the tube to handle more level before breaking up to a moderate distortion. At 140 volts, maximum voltage is applied to the tube producing slight saturation and warmth. Sweepable high-pass and low-pass filters can be assigned 'pre or post' tube, allowing you to focus the tube effect on a particular frequency band or cause the tube to react in a different way. Finally, an output level control provides attenuation or boost through an oversized Jensen transformer specially selected for its big bottom end and vintage character.

Enhancing a snare with a touch of distortion can increase presence without losing dynamic range. Blending in some overdrive to a bass track can add clarity without overpowering. Adding distortion to a vocal track can add character and sizzle to cut through the mix without over-compression. The Space Heater 500's amazing 'adjustability' allows it to be used as a subtle effect or as a high gain monster. And no matter your approach, it is sure to find its way on nearly everything you record!

The Space Heater 500… to infinity and beyond!

  • Studio grade 12AX7 tube overdrive
  • 35, 70 & 140 volt Heat switch to set plate B+ voltage
  • Transformer coupled output for vintage tone
  • Variable HPF & LPF filters to focus distortion

Features And Specs

Specifications are subject to change without notice.
Circuit type:  Thermionic Gain stage with solid state input and output buffers
Frequency response: 20Hz - 20KHz ± 1dB
Total harmonic distortion:  Varies with Drive and Level settings
Dynamic range:  92dB
Input impedance – bypassed:  50K
Input impedance – active:  1M
Maximum input:  +20dBu
Maximum gain:  32dB@140V, 27dB @70V, 13dB @35V
Clip level - output:  +22dBu 
Output impedance:  100Ω 
Equivalent input noise:  -102dBu 
Noise floor:  -70dBu 
Intermodulation distortion:  Varies with drive and level settings 
Common mode rejection ratio:  -60dB
Unity gain control position:  Drive & level at about 11 o'clock
Features   
Controls: Drive, Level, Hi-Cut filter, Lo-Cut filter
Switches:  "Heat", EQ Pre/Post, IN 
Switches - rear panel:  Heater polarity selection
Filter slopes:  12dB/Octave 
Omniport function:  Unbalanced instrument input
General   
Construction:  500 Series module
Finish: Durable powder coat
Size: (W x H x L) 5.3" x 1.6" x 6.7" (134mm x 40mm x 170mm)
Weight:  1.55lb
Shipping size: (W x H x L): 6.7" x 1.9" x 9.1" ( 170mm x 48mm x 231mm)
Shipping weight: 2lb
Conditions: For use in dry locations only between 5°C and 40°C
Warranty:  Radial 3-year, transferable
Type de matériel Effets

Commander

RADIAL - SPACE HEATER 500

RADIAL - SPACE HEATER 500

0 €

Veuillez patientez...

Pour le moment, M2M Pro a choisi la relation directe avec ses clients.
Les ventes, demandes d'offres et prix... se font via ce formulaire.
N'hésitez pas à prendre contact avec nous pour toute autre question.












* Champ requis